Advanced Technology UMA brand® Tintable: Product Number 1106
Water Born, Bonding Primer Sealer, VOC: less than 100 g/l

• Meets California VOC Rules for Primers

• Urethane Modified Acrylic - Properties of both a primer and adhesive

• Makes paint stick to tough-to-paint surfaces, including ceramic tile, porcelain, glass, Formica and melamine laminates, PVC, fiberglass, many plastics, Kynar and Silicone Polyester siding, aluminum, galvanized and many metals, wood

• Quick drying, levels smoothly

• Tintable to deep colors with universal tint colors

• Interior / Exterior – Low Temp. & High Humidity applications

• Top coat with all paints in several hours

Product Description: XIM Advanced Technology UMA Tintable Base version of Advanced Technology UMA is a waterbased Bonder that, like the traditional white version, has both primer and adhesive-like properties. It provides excellent adhesion and wet adhesion to “Hard-to-Paint” surfaces, even when wet. Sanding may not be necessary for most clean and dull paintable surfaces, but sanding or dulling the surface is required for maximum adhesion, specifically on surfaces such as tile, porcelain and glazed block. UMA can be used for both indoor and outdoor applications. and can be used with Oil/Alkyd, Latex, Urethane, Epoxy and Lacquer top coats. Advanced Technology UMA will form a hard film when fully cured. Its resistance to scratch testing can vary with the type of surface and the degree of cure, however, when full cured, they will provide long lasting adhesion. For maximum Rust Protection, use solvent based XIM 360 Rust Inhibiting Primer or water based XIM Corrosion Control.

Product Use: Advanced Technology UMA Tintable Base can be tinted to pastel or deeptone colors using up to four (4) ounces of universal tinting color per gallon. To achieve pastels or increase the hiding, white tint may have to required. Color matching is at the descretion of the purchaser or applicator. It is an ideal prime coat for Wood, Metals, Plaster, Hardboard, Most Plastics, Fiberglass, Formica, Tile, Porcelain, Glazed Block, Glass, etc. Also recommended for priming Kynar and Silicone Polyester pre-coated siding. Note: Because there are many types of surfaces, plastics and composite materials, always test a small area first for adhesion and topcoat compatibility before starting. When priming Kynar and Silicone Polyester pre-painted siding at least two test patches in different areas is a must to demonstrate adhesion that is acceptable to you. Not recommended for tubs, sinks or showers where continuous water or hot water contact occurs. Not recommended for use on polyethylene, polypropylene, Teflon or nylon. Not recommended for below grade application. For extra corrosion protection on iron and steel use XIM 360 Rust Inhibiting Primer. On extremely porous surfaces or severe staining types of wood additional coats of UMA may be required. Certain staining agents, such as tannic acid or mineral salts from water may require XIM’s solvent based stain killers. Advanced Technology dries to touch in about 30 to 45 minutes and will reach full hardness in 7 to 10 days depending on temperature, humidity and film thickness. It can be nib sanded after about 3 hours and lightly sanded 24 hours after application. It can be used for indoor or outdoor applications and can be top coated with all top coats including latex, oil-alkyds, lacquers, urethanes and epoxies. Shelf life is 36 months, unopened at room temperature of 77 degrees F.

Product Preparation: Advanced Technology UMA is ready to apply from the can. If tinting, use universal tinting colors uo to four (4) ounces per gallon. Shake or mix well before using. If thinning, XIM’s Latex X-Tender is recommended.

Surface Preparation: Surface must be clean and dry, free from all grease, wax, oil, polish, loose paint, dirt, rust or other contamination. Clean with a strong abrasive detergent, rinse well and allow to dry. Scrub moldy or mildewed surfaces with bleach and rinse well. When priming hard, glossy surfaces, metal or pre-finished siding clean per SSPC-SP1, which is solvent cleaning. Wipe down the surface with XIM GON Cleaner or Xylene. Do not use mineral spirits, turpentine solvents that will leave oily residues. For very hard, glossy surfaces, roughing the surface with silicon carbide sandpaper before applying the Bonder necessary for best adhesion.

How to Apply: Apply this Bonder by synthetic fiber brush, ¼ inch synthetic roller or by spray. Avoid any excess foaming by thoroughly wetting the brush or roller with water before applying. The temperature of the surface and the surrounding air should be between 35 deg. F and 100 deg. F. It will dry to touch in about 30-45 minutes under standard conditions (77 deg. F and 50% relative humidity). Thicker coats will take longer to dry. It will generally become hard in about 7 - 10 days. They can be top-coated in 3 hours after application. When top coating with 2-component paints allow 24 hours before painting. Do not paint in direct sun or on a hot surface. Stop application two hours before a heavy dew or rain. If possible plan your painting to avoid rain, moisture and high humidity for the first 24 hours of curing. Advanced Technology covers about 450 square feet per gallon. Caulk seams and edges after priming.

Clean-Up: Clean-up with soap and water. If the UMA “sets-up”, or when cleaning up splatters or spills use warm water or lacquer thinner.

Potential Applications:
Building Material Plastic: More and more plastics are used in the building industry, including PVC sheeting and piping, vinyl shutters, vinyl molding and mill work, laminated Formica paneling and cabinets as well as fiberglass garage doors and other molded parts. First, remove old and loose paint then clean away wax, polish, grease, oil and other contaminants from the surface with a strong abrasive detergent. Wipe the surface with a cleaning solvent such as XIM GON Cleaner or xylene. Dry, then scuff sand the surface for maximum adhesion. Apply the XIM Bonder. Wait 3 hours and topcoat. Test for adhesion before starting the job. Advanced Technology UMA is recommended for priming Kynar and Silicone Polyester pre-coated siding. When priming Kynar and Silicone Polyester pre-painted siding at least two test patches in different areas is a must to demonstrate adhesion that is acceptable to you.
Tile, Glazed Block and Brick, Porcelain: Decorative surfaces such as these can be restored and painted. First remove old paint and debris. Repair or patch any broken or damaged areas. Then clean away any wax, polish, grease, oil and other contaminants with a strong abrasive detergent. Wipe the surface with a cleaning solvent such as XIM GON Cleaner or xylene. For maximum adhesion scuff sand or etch the surface with XIM’s etching cream, Etch-I-M, rinse well to remove any etching residues and allow to dry. Apply the UMA Bonder and allow to dry for 3 hours then apply the topcoat. Not recommended for sinks, tubs or shower areas where continuous water or hot water can be present. Note: where flexible seams or soft caulking are present, do not paint over with the UMA. Always plan your job ahead and caulk after painting. Always caulk edges or seams that can trap and hold moisture and, therefore, become the source of coating failure. For exterior jobs - where high water contact is expected or where moisture or dew may accumulate, two coats of the top coat paint are recommended.
Non-Ferrous Metals: With XIM Advanced Technology UMA brand Bonder you can get a long lasting, durable job when painting aluminum doors and window frames, aluminum and copper flashing and trim as well as galvanized steel. Clean away all corrosion and any old paint, dirt, wax and grease. Wipe the surface with a cleaning solvent such as XIM’s GON Prep cleaner. Allow to dry then apply the UMA Bonder (only one coat is required) Allow the UMA to dry for three hours, then apply the top coat.